Kogeki 15" flow formed wheel for NA and NB

100% of 100

As low as $716.00


Part number

Strong, light and affordable meet sexy. Our exclusive flow formed wheel for the NA and NB!

Customize Kogeki 15" flow formed wheel for NA and NB

* Required Fields

Your Customization
Kogeki 15" flow formed wheel for NA and NB
Available in 15x8 & 15x9 in Black, Bronze Metallic and Gunmetal Grey Metallic.
Kogeki 15" flow formed wheel for NA and NB

In stock



    Kogeki means "attack" in Japanese - seemed appropriate since these are intended for attacking your favorite corners, whether they're on a track or your favorite backroad.

    These flow formed wheels are exclusive to Flyin' Miata and built for us by a major wheel manufacturer. They're high-pressure cast for less porosity, then the rim is spun-forged. They were designed specifically for the NA/NB Miata to ensure clearance for all FM and stock brake setups and for the perfect fit under the fenders. Because we know they'll be used hard, they're rated for 550kg (1213 lbs) of load instead of the more standard 500 kg (using J2530 JWL standards). They also have knurling to prevent tire slip.

    It's hard to overstate how much brake clearance they have - we can't guarantee they'll fit with everything, but that have more than 1/2" additional clearance than our previous wheel. 

    And seriously, just look at them. Yummy.

    You can fit a 225/45-15 on a 9" wheel under unmodified NB fenders, although NA fenders will require a roll. The 9" wheels won't fit with stock diameter springs (such as the FM springs), but they will fit with a 2.5" or smaller spring (such as the Fox or V-Maxx). The 8" wheels will fit fine with stock-format springs, will fit either a 205/50-15 or a 225/45-15, and will fit NAs and NBs with no fender modifications. Obviously, the use of wheel spacers will affect this fitment.

    Centering rings aren't required, as the wheel will center on the taper of the lug nuts, but centering rings do make installation a tick easier.

    You can use stock lug nuts and chrome sockets, but it's close - 21mm impact sockets probably won't clear, 19mm impact sockets (as used with our 19mm lug nuts) probably will, but be careful. Chrome 19mm sockets should have plenty of room. 

    If you choose to upgrade your wheel studs (recommended if spacers are used or if the car will see extreme use), the 1990-93 NA6 uses 0.507" studs on all four corners. Other NAs and NBs use 0.579" on the rear and 0.507" on the front.

    Note that wheels are sold individually, so make sure you order 4.


    15x8: 12.4 lbs, +36 offset, 67.1 mm hub bore

    15x9: 13.45 lbs, +36 offset, 67.1 mm hub bore

    We recommend that any wheel used on the track be inspected regularly for cracks and fatigue as part of proper maintenance. 


    More Information
    Part number M16-530x0
    Designed for: 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1999, 2000, 2001, 2002, 2003, 2004 (non-MSM), 2005 (non-MSM), 2004-05 MSM, 2016 MX-5, 2017 MX-5 soft top, 2017 MX-5 RF, 2017 Fiat 124 Spider, 2018 MX-5 soft top, 2018 MX-5 RF, 2018 Fiat 124 Spider, 2019 MX-5 soft top, 2019 MX-5 RF, 2019 Fiat 124 Spider, 2020 MX-5 soft top, 2020 MX-5 RF, 2020 Fiat 124 Spider, 2021 MX-5 soft top, 2021 MX-5 RF
    Fits Exocet? Yes
    California emissions Emissions regulations do not apply
    Proposition 65 Warning: Cancer and reproductive harm
    Flyin' Miata exclusive Yes
    Warranty 1 year
    Write Your Own Review
    You're reviewing:Kogeki 15" flow formed wheel for NA and NB
    Your Rating
    © Flyin' Miata. All Rights Reserved.