Welcome to Flyin' Miata!

Search results for 'turbo kits'

List Grid

Set Descending Direction

1-50 of 189

  1. 1
  2. 2
  3. 3
  4. 4
  1. MAC boost control solenoid kit
    Electronic boost control hardware Learn More
  2. Snazzy messy pile of bushings
    An inexpensive way to refresh your suspension. Learn More
  3. Complete kit

    V-Maxx Classic coilovers matched with FM sway bars: a complete handling package for a low price.

    Learn More
  4. You will reuse your stock upper mounts as shown

    From: $2,199.00

    To: $2,449.00

    Sway bars plus our excellent FOX coilovers

    Learn More
  5. Sexy closeup of the high traction surface.
    Keep your feet from slipping off your pedals at embarrassing moments. Learn More
  6. Flyin Miata tool kit (1991-00 and MSM engine)

    FM's special tools to make a timing belt change easy. Includes our crank holding tool, cam gear Ninja Tool, crank and cam seal installers.

    For 1991-00 and Mazdaspeed models.

    Learn More
  7. EGR blockoff plate
    Stainless steel plate to block off the EGR fitting Learn More
  8. Shown without edge trim
  9. Trackspeed fuel pump rewire kit
    Bulletproof your main relay! Learn More
  10. Shown assembled using the stock upper mounts (not included)

    From: $1,750.00

    To: $2,249.00

    The best suspension we've ever offered for the NB.

    Learn More
  11. Complete kit.

    Regular Price: $199.00

    Special Price $99.99

    Harness the power of lasers to make your alignment even easier! Compatible with v3.0 stands only! Learn More
  12. Magnecor sequential LS coil 8.5mm wire set for 2001-05 engines
    Replacement plug wires for cars with LS coils. Learn More
  13. Includes all parts needed for installation.
    For those who need lots of fuel and need it right now. Learn More
  14. Note: this is not the crossflow version. It differs slightly in the location of the inlet.
    Our Stage 1 Airflow kit for our crossflow radiator Learn More
  15. Stage 2 airflow kit.
    Maximum airflow for maximum cooling. Learn More
  16. Stage 2 airflow kit (non-crossflow version shown)
  17. Stage 1 Flyin Miata airflow kit (NB)
  18. Timing belt kit (NB 1999-00 and MSM)
    Everything you need for a timing belt change! Learn More
  19. Factory lower shock shaft bushings, NB (set of four)
    Consider replacing these when doing a suspension change. Learn More
  20. Shifter rebuild kit (2002-05 6-speed)
    Make your shifter feel new again! For 6-speed transmissions built after August 2001. Learn More
  21. The kit might vary slightly from this picture.
    Run your Miata on ethanol or gasoline without having to adjust anything - E0 to E100 fuel on the fly! Learn More
  22. 99-05 Complete Fuel Rail Kit
  23. FM fuel rail only
    Rail only, no lines Learn More
  24. Passenger side heater hose
    Factory replacement part Learn More
  25. Eccentric bolt lock kit
    New parts along with the exclusive Paco Motorsports eccentric lock. Learn More
  26. M10x1 inverted flare to NPT adapter
    Install a proportioning valve in your Miata without flaring tools! Learn More
  27. With black face and bezel installed
    A highly accurate wideband controller integrated into a standard 2 inch gauge. Now faster with a wider range of readings! Learn More
  28. Weld-in version
    Available in both no-weld and welded versions Learn More
  29. V-Maxx secondary spring kit
    Just the helpers, ma'am. Learn More
  30. Drill and tap for installing hood lifts
    Drill and tap 6x1.0 threads. Learn More
  31. Blank gauge panel for NA/NB dashboards
    Build your own gauge cluster. Learn More
  32. The separator
    Cut down on oil consumption during hard use. Learn More
  33. Rear main/crank seal for NA/NB
    We recommend changing this with every clutch change. Learn More
  34. 3" lift kit. Shown with 215/65-15 tires and spacers. Effective offset is +20 front, +5 rear.
  35. The lock in place.
    Your alignment will never slip under load again. Learn More
  36. 5mm 5x114.3 wheel spacer
    Need to space your wheels out just a little bit more? Here you go! Learn More
  37. 5 mm 4x100 wheel spacer
    Need to space your wheels out just a little bit more? Here you go! Learn More
  38. Driver's side heater hose
    Factory replacement part Learn More
  39. Hardware not shown
    Turn a set of frame rails into a full butterfly brace! Learn More
  40. Complete butterfly
  41. Dual valve spring kit
    For the most extreme Miata engine builds - with titanium retainers. Ooooo. Learn More
  42. Big nose crank seal
    Recommended with every timing belt change. Learn More
  43. Complete polyurethane bushing kit for NA and NB
    Banish rubber from your suspension with this complete polyurethane bushing set. Learn More
  44. Timing belt and pulleys
    Just the belt and pulleys. As used in our timing belt kit. Learn More
  45. Rear stainless steel brake line kit
    Two rear lines and associated parts Learn More
  46. Flyin' Miata brake lines for Wilwood front calipers, NA/NB
    Replacement lines for Wilwood-equipped cars Learn More
  47. May differ slightly in appearance
    Useful when you remove the stock proportioning valve. Learn More
  48. 3 mm 4x100 wheel spacer
    Need to space your wheels out just a little bit? Here you go! Learn More
  49. MSM check valve kit

    Make the oil separator in your MSM work as Mazda intended!

    Learn More
  50. Wilwood rotor hardware
    This should be changed when you change rotor rings. Learn More

List Grid

Set Descending Direction

1-50 of 189

  1. 1
  2. 2
  3. 3
  4. 4