Welcome to Flyin' Miata!

Search results for 'turbo kits'

List Grid

Set Descending Direction

1-50 of 141

  1. 1
  2. 2
  3. 3
  1. MAC boost control solenoid kit
    Electronic boost control hardware Learn More
  2. Flyin Miata tool kit (1991-00 and MSM engine)

    FM's special tools to make a timing belt change easy. Includes our crank holding tool, cam gear Ninja Tool, crank and cam seal installers.

    For 1991-00 and Mazdaspeed models.

    Learn More
  3. EGR blockoff plate
    Stainless steel plate to block off the EGR fitting Learn More
  4. Trackspeed fuel pump rewire kit
    Bulletproof your main relay! Learn More
  5. Shown assembled using the stock upper mounts (not included)

    From: $1,750.00

    To: $2,249.00

    The best suspension we've ever offered for the NB.

    Learn More
  6. Complete kit.

    Regular Price: $199.00

    Special Price $99.99

    Harness the power of lasers to make your alignment even easier! Compatible with v3.0 stands only! Learn More
  7. Prototype shown.Actual product varies slightly.
    A great tool for a club or a racer. Do a full suspension setup at home! Learn More
  8. Passenger side heater hose
    Factory replacement part Learn More
  9. Driver's side heater hose
    Factory replacement part Learn More
  10. You will reuse your stock upper mounts as shown
  11. Complete butterfly
    Lighter, stiffer, lower price. Learn More
  12. Hardware not shown
    Turn a set of frame rails into a full butterfly brace! Learn More
  13. MiataHubs replacement bearing with included hardware
    If all goes according to plan, you'll never need this. But just in case... Learn More
  14. 5 mm 4x100 wheel spacer
    Need to space your wheels out just a little bit more? Here you go! Learn More
  15. Weld-in version
  16. With black face and bezel installed
    A highly accurate wideband controller integrated into a standard 2 inch gauge. Now faster with a wider range of readings! Learn More
  17. V-Maxx secondary spring kit
    Just the helpers, ma'am. Learn More
  18. Drill and tap for installing hood lifts
  19. Blank gauge panel for NA/NB dashboards
    Build your own gauge cluster. Learn More
  20. The separator
  21. Rear main/crankshaft seal for NA/NB
    We recommend changing this with every clutch change. Learn More
  22. Eccentric bolt lock kit
    New parts along with the exclusive Paco Motorsports eccentric lock. Learn More
  23. The lock in place.
    Your alignment will never slip under load again. Learn More
  24. 3" lift kit. Shown with 215/65-15 tires and spacers. Effective offset is +20 front, +5 rear.
  25. 3 mm 4x100 wheel spacer
    Need to space your wheels out just a little bit? Here you go! Learn More
  26. May differ slightly in appearance
    Useful when you remove the stock proportioning valve. Learn More
  27. M10x1 inverted flare to NPT adapter
    Install a proportioning valve in your Miata without flaring tools! Learn More
  28. Dual valve spring kit
    For the most extreme Miata engine builds - with titanium retainers. Ooooo. Learn More
  29. Big nose crank seal
    Recommended with every timing belt change. Learn More
  30. Timing belt and pulleys
    Just the belt and pulleys. As used in our timing belt kit. Learn More
  31. Complete polyurethane bushing kit for NA and NB
    Banish rubber from your suspension with this complete polyurethane bushing set. Learn More
  32. These are actually rear brackets, but it's the only picture we have right now...
  33. Brackets for rear NA/NB Little Big Brake Kit
  34. Rear stainless steel brake line kit
    Two rear lines and associated parts Learn More
  35. Flyin' Miata brake lines for Wilwood front calipers, NA/NB
  36. Wilwood rotor hardware
    This should be changed when you change rotor rings. Learn More
  37. Black shown (no longer available)
  38. Flyin' Miata Big Fuel kit (1.8 in NA6)
    Everything you need to feed an engine that consumes mass quantities of fuel. Learn More
  39. Exhaust/intake valve stem seal
    Fits exhaust valves on all NA and NB engines as well as the intake on the NA6. Learn More
  40. dip stick tube o-ring
    Fixes leaks at the bottom of the dip stick Learn More
  41. O-ring for oil filler cap
  42. 10 mm 4x100 wheel spacer
    For 10 mm of extra space inside your wheels Learn More
  43. FPR adapter
    Fit an FPR to a 1/4 NPT hole Learn More
  44. O-ring for oil pump
    Replace when the pump is out. Learn More
  45. NA PCV valves look different than this but use the same grommet
  46. Clutch accessory kit for FM level 2 NA/NB clutch
    Replacement pilot and throwout bearing Learn More
  47. Clutch accessory kit for FM level 1 NA/NB clutch
  48. Replacement parking brake cables for Wilwood calipers
  49. Thermostat housing o-ring
    If you need it, you need it. Learn More
  50. Clutch alignment tool
    If you don't have one, you'll wish you did. Learn More

List Grid

Set Descending Direction

1-50 of 141

  1. 1
  2. 2
  3. 3