This is a used FM lightweight trailer hitch, 1999-05 with the removable ball mount. There are a couple small scuffs but overall in good condition. All of the details can be seen at http://www.flyinmiata.com/index.php?deptid=5684&parentid=0&stocknumber=29-51000%20%20BALL

Fits 1999-2005
Price: $200

Out with the old in with the new! We upgraded these painted mild steel lines with stainless steel lines. These function just as well and are less a less expensive upgrade to your turbo kit.

Sold at $175 (lines only) or $120 (upgrade within turbo kit purchase)
Compare to our stainless lines sold at $249 (lines only) or $179 (upgrade)

Additional information can be found at http://www.flyinmiata.com/index.php?deptid=4524&parentid=0&stocknumber=22-61500%20%201994-05

Part# 22-61500

Fits 1994-2005
Price: $175

Here's an old production (but still new) 2.5" turbo muffler for 90-97 Miatas. You'll need to fabricate your own midpipe to run between your cat & this muffler. Selling as-is / no warranty.
Does not include any hardware, including the extra hanger for the new tips.

Fits 1990-1997
Price: $225

What looks like a bag of wires and tubes is actually our superseded FM O2 Pressure Switch. It was replaced by our O2 Signal Modifier (Additional info). This unit performs the same function, but it has more wires, take a bit more work to install, and more time to setup. Don't worry, the kit includes instructions.

Fits 1990-2005
Price: $80

Everything you need to know-
http://www.splitsec.com/products/psc1/PSC1005.htm

This unit is NIB, we bought it and never did anything with it. Our loss is your gain!

Fits 1990-1993
Price: $300

Here's a VICS lower intake manifold with extra bungs welded in for 1 additional injector per runner, as previously used in the Link piggyback turbo kits. While we're no longer a fan of this setup ever since the Hydra ECU came out, this would be a really sweet setup to do a custom water injection setup with one jet per runner! (We'll give you $75 back as a core return if you return your stock LIM back to us after installing one of these.)

Fits 1999-2000
Price: $150

Here's a brand new Boomslang harness for putting a GReddy Emanage Ultimate in your 96-97 Miata.

Fits 1996-1997
Price: $145

Is your old main crank pulley / damper tired? Is the rubber no longer doing its job? Refresh your engine with one of these! Brand new Mazda damper for 99-05 cars.

Fits 1999-2005
Price: $149

Here we have a new set of Eibach 2.5" race springs. 8" free length, 750 lb rate. These were custom ordered for a Ground Control set and then decided against. This price is for the pair.

Fits 1990-2005
Price: $120

Want to learn about how to attach a supercharger to your engine and make mad power? Well, here are some ideas for you.

Fits 1990-2005
Price: $20

Doing a custom ECU project? Use this solder-in header plug to make a custom harness!

We also have pin & plug kits for the other side of the harness- inquire if interested.

Fits 1990-2000
Price: $75

Here's a used NA 1.8 intake manifold for a 1.2L Whipple blower. Manufactured by BEGi. As-is, no warranty.

Fits 1994-1997
Price: $250

We have no idea where this came from. It's an aluminum bypass valve. No markings. To be honest, this would probably be a really good BOV for a high boost car- it's solid. It is built like an external wastegate, until until you pick it up and realize it's aluminum. It has roughly a 2 5/8 flange inlet (bolt center to center) and a 1 3/4" round outlet. Great for a DIY project.

Fits 1990-2005
Price: $50

These shocks are famous! They've been in magazines. What magazines? Well, we're not really sure. But they came off our 2006 MX-5, which spent the first 3500 miles of its life as a press car. Provenance!
Approximately 4000 miles, so basically brand new. As used on the factory sport suspension.

Fits 2006-2008
Price: $200

Here's a NIB Link Piggyback like we used to use in 99-05 FM2 cars. Recommended 9 psi max for any application. Great for 1999 CA cars as it was part of the CARB legal turbo kit!

Fits 1999-2005
Price: $500

Get your own spring, save money! This is for the complete valve sans the spring that moves the piston.

These were once used in the FM turbo kits, but alas, were replaced by the lighter and better sealing GFB valves. The footprint is 1 3/8" from the 2G DSM turbo cars.

Part 05-90905

Fits 1990-2005
Price: $30

This is useful for measuring the inlet and outlet temperatures of an intercooler.

Westach Part Number: 399S7E
The sensor requires a 1/8" NPT hole
1-inch tip
4-foot leads
212°F = 212 ohms

Not to be used to measure exhaust gas temperatures, or fluids. There are different senders for those applications.

Check out Westach's website to see which gauges work with this sender.

FM's part number: 23-16900 AIR
Original Retail: $41.95

Fits 1990-2005
Price: $10

No, we are not giving them away for free!

Our previous turbocharger systems used all sorts of different silicone hose sizes. Our current turbocharger system only uses one silicone hose piece. That means we have all these great sizes but nothing to use them on. So we're offering them to you at 60% off!

We have lots more than what you see in the picture. We have these sizes/colors on sale:

Part Number:
36-60000: 1.375"ID x 2.5"L: $1.58ea (Red only)
36-60003: 1.5"ID x 1.5"L: $1.30ea (Black only)
36-60015: 2.0"ID x 2.0"L: $1.98ea (Black, Red)
36-60020: 2.25"ID x 2.0"L: $2.38ea (Black, Red)
36-60025: 2.25"ID x 2.5"L: $2.38ea (Black, Red)
36-60040: 2.75"ID x 2.0"L: $2.38ea (Blue, Red)
36-60050: 3.0"ID x 2.0"L: $2.38ea (Black, Red)
36-60120: 2.25"ID x 12"L: $9.18ea (Black)
(36-60120 is orange on the inside)

Also, all the blue silicone hose pieces are blue on the outside and orange on the inside.

Need some clamps with those? Not a problem!

The outside diameter of the hoses are as follows:
1.375" hose = 43mm
1.5" hose = 48mm
2.0" hose = 59mm
2.0" Blue hose = 61mm
2.25" hose = 66mm
2.5" hose = 72mm
2.75" hose = 79mm
3.0" hose = 85mm
Just a reminder, the outside diameter can increase when you slide a silicone hose onto a tube.

Constant Torque clamps - not on sale:
36-70000: 33-57mm - $4.50ea
36-70010: 52-76mm - $4.50ea
36-70020: 59-83mm - $4.50ea

Winzer clamps - on sale, 40% off!:
36-70130: 50-65mm - $1.17ea
36-70140: 58-75mm - $1.35ea
36-70145: 68-85mm - $1.38ea

All of the prices reflect the 60% and 40% discounts.

Fits 1990-2009
Price: $0

Here's an assortment of Aquamist water injection nozzles. We have a random amount of .6, .8, .9, and 1.0mm nozzles.
Price is per nozzle.

Fits 1990-2005
Price: $10

Here's a used NB intake manifold for a 1.2L Whipple blower. Manufactured by BEGi. As-is, no warranty.

Fits 1999-2005
Price: $250

Here's a used set of H beam rods. They were just re-bushed on the small end. We can also special order a set of big end stretch bolts if you like at $128 for a set. (recommended)

Fits 1990-2005
Price: $795

Here's a VTCS lower intake manifold with extra bungs welded in for 1 additional injector per runner, as previously used in the Link piggyback turbo kits. While we're no longer a fan of this setup ever since the Hydra ECU came out, this would be a really sweet setup to do a custom water injection setup with one jet per runner! (We'll give you $75 back as a core return if you return your stock LIM back to us after installing one of these.) P.S. for a fee our machine shop can remove & weld up the holes from the VTCS butterflies if you have a standalone ECU.

Fits 2001-2005
Price: $150

This is a RacingBrake brand big brake kit for the NC miata. We had this kit installed on one of our cars for at most 1,000 miles.

This kit includes:
- 2 Two-piece center-mount rotors
- 2 4-Piston calipers
- 2 Aluminum adapters
- 2 Wheel spacers

Requires 17" or larger wheel size. This brake kit will fit most 17" wheels with the exception of 17” Enkei RPF1 wheels.

There are some chips in the caliper paint as well as some paint bubbling near the fluid inlets from brake fluid contact.

Please email salvage@flyinmiata.com for more information.

Fits 2006-2009
Price: $995

Here is a set of unused OEM rear brake pads for your 1994-2000 Miata. Pads only, no hardware.

Fits 1994-2000
Price: $35

These parts took a tumble and have some chips in the powder-coating to show for it. They can be sold individually for $100.00 each or be sold as part of the kit for $205.00. Compare to $120.00 and $225.00 normally. These will only fit on the 90-97 style hitches.

<a href="http://www.flyinmiata.com/index.php?deptid=5684&parentid=0&stocknumber=29-50910%20%20BALL">Additional information on the ball mount</a>

<a href="http://www.flyinmiata.com/index.php?deptid=5684&parentid=0&stocknumber=29-50000%20%20BALL">Additional information on the kit</a>

Part #29-50910 ball mount
Part #29-50000 kit

Fits 1990-1997
Price: $100

Have a big turbo? Need big injectors? RC 1200cc peak & hold (low impedance) injector set of 4 with electrical adapters.

<a href="http://www.rceng.com/Peak-Hold-Injector-PL9-1200-P18C5.aspx">Additional information</a>

Fits 1990-2005
Price: $270

The same kit is sold at www.miatamania.com for $160. It is not used and is in perfect condition. Will only fit a 90-93 miata. <a href="http://www.miatamania.com/Shop/ViewProducts.aspx?PlateIndexID=74441">Additional information</a>

Fits 1990-1993
Price: $100

This is a used MSD ignition boost retard. Timing management for low boost turbo and supercharger kits. Retards timing 6 degrees under boost, starting at 4 psi. This gives you good off-boost response while keeping things safe when the power comes up. 1990-97 models only.

Fits 1990-1997
Price: $100

Planning on building a high-RPM or high-boost motor? You'll want these Carrillo H-beams! Fits B6 & BP motors.

<a href="http://www.flyinmiata.com/index.php?deptid=4530&parentid=0&stocknumber=04-66000">Additional Information</a>

These are being sold for $250 off retail, since they are used.

Fits 1990-2005
Price: $980